Before & After Photos

This homeowner in Unionville, CT reached out to us with a drafty, uncomfortable home. He believed that there was an issue with the attic. Our Home Comfort Specialist came out to the home and noted that the insulation in the attic was not adequate at all, and in some places the insulation was quite literally falling apart. This was particularly evident in the kneewalls in the main section of the house, which had very little insulation. 

Luckily, Fogarty's Home Services had the perfect solution for this customer! We were able to help them by re-insulating their attic. In the kneewall space, we first started by bagging and removing the batt insulation on the wall. We then vacuumed out all loose insulation. 

After that, we got to work insulating the kneewall. We installed blocks of SilverGlo™ foam insulation board between the ceiling joist bays. We then air sealed between these blocks. Since SilverGlo™ has a radiant barrier on both sides, it reflects roof heat out in the summer and house heat back in in the winter -- ensuring that the homeowner will be comfortable. They can already feel the difference in their home! 

This room over the garage is being renovated.  The homeowner wanted to be sure his home is properly insulated.  One of the treatments our team did in this room was to insulate the kneewall.  A kneewall is the triangular space under the sloped roof and behind the wall of the room.  We installed our Foamax polyisocyanurate foam board on the exterior walls.  Foamax provides superior insulation and it is flame retardant.  The homeowner can rest assured the knee walls in this room are properly insulated. 

This Home in Canton, CT was experiencing drafts and needed a Rim Joist insulation.

This homeowner in Granville, MA called us saying that he had found mold and damp insulation in his attic. Our Home Comfort Specialist came out to the home and was able to do a full evaluation. He noted that among other issues such as improper ventilation, the attic was not air sealed and had ineffective insulation. 

In order to help this attic customer, we first had to remove the old fiberglass insulation. There were two types of insulation, blown-in fiberglass and fiberglass batt insulation. We bagged the batt insulation and vacuumed the rest out with a long hose. 

We then set to work re-insulating the attic. We first air-sealed all cracks and gaps in the attic floor using Zypfoam one part spray foam. We used our TiteShell™ can light covers to cover up the can lights and sealed around them. 

After that, we insulated the attic floor using our TruSoft™ blown in cellulose insulation. We insulated to R-60, which is the recommended level of insulation for attics in our region. 

Now, this homeowner has a much more comfortable home - he was already feeling a noticeable difference less than a week after this job was completed! 

This homeowner in Granville, MA called us hoping that we would be able to help him with mold in his attic. He wanted his insulation replaced and the mold removed. Since attics are vented, we should think of them thermally as outside in the winter. In summer because of the suns radiant heat, they are much worse than outside, reaching 130˚ on summer days. Clearly, we need to keep an absolute boundary between our living space and the attic so inside air doesn’t move to the attic in the heating season (convection), and heat doesn’t pass up through our ceilings in winter (conduction), and down from our ceilings in the hot summer (conduction, radiation). To reduce overall air leakage, the attic is the first priority because warm air rises to the top of the house and finds any and all holes to leak out into the cold vented attic and is lost. Holes, gaps and joints include between drywall and framing at the top of walls, around pipes, wires, electric boxes, fixtures, duct, penetrations, ceiling grilles and joints in framing. And the only reason cold air leaks in from the outside at the lower levels of the house, is that warm air leaked out of the top and created a suction at the bottom. 

We had the perfect solution for this customer. Adding insulation in an attic without sealing all air leaks first should never be done, because it is just burying air leaks and making them impossible to seal later - and insulation DOES NOT STOP air leaks. That’s why, in this solution, we first carefully air seal the many various points where air from the home leaks up into the attic and is lost. Our premium TruSoft™ cellulose insulation is blown to the optimum R-value (typically R60). TruSoft™ will not burn, get moldy, or attract pests. Blown insulation fills all gaps and odd shaped voids, and by filling over framing members, “thermal bridging” is avoided.